coffee-forum.net
Promoting coffee discussion.

Main
Date: 04 May 2007 07:46:38
From:
Subject: Re: size of tube from pump output to boiler inlet on silvia
Bummer. McMaster Carr said they can't send me the tubing "due to the
ever increasing complexity of United States export regulations." Oh
well, I guess it's a good thing they're keeping the terrorists from
enjoying their espresso.







 
Date: 04 May 2007 11:47:09
From:
Subject: Re: size of tube from pump output to boiler inlet on silvia
On May 4, 11:55 am, "Craig Andrews" <alt.cof...@deletethis.rogers.com >
wrote:
> <Dr.Xen...@gmail.com> wrote in message
>
> news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
>
> That's Bullshit & I posted you an answer for a Toronto source. I live in
> North Etobicoke & Fairview Fittings is about 10 minutes away from me &
> has everything you could possible need.
> Cheers!
> Craig.

It turns out Fairview Fittings doesn't sell any metric tubing. They
referred me to a company called Hydraline, who referred me to a
company in Pickering called Williams, neither of whom carry PTFE
tubing.



  
Date: 04 May 2007 15:35:46
From: Craig Andrews
Subject: Re: size of tube from pump output to boiler inlet on silvia

<Dr.Xenon1@gmail.com > wrote in message
news:1178304429.155861.87920@l77g2000hsb.googlegroups.com...
> On May 4, 11:55 am, "Craig Andrews" <alt.cof...@deletethis.rogers.com>
> wrote:
>> <Dr.Xen...@gmail.com> wrote in message
>>
>> news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
>>
>> That's Bullshit & I posted you an answer for a Toronto source. I live
>> in
>> North Etobicoke & Fairview Fittings is about 10 minutes away from me
>> &
>> has everything you could possible need.
>> Cheers!
>> Craig.
>
> It turns out Fairview Fittings doesn't sell any metric tubing. They
> referred me to a company called Hydraline, who referred me to a
> company in Pickering called Williams, neither of whom carry PTFE
> tubing.
>

Hmm, I figured that Fairview would have it, or know somone who does. I
remembered another contact # from someome I met in a commercial supplier
plumbing shop & the contact specializes in B.P.P.T., N.P.T., & Metric
fittings & tubing/s. I called them & someone in that division is looking
for me. It's getting a little late in the day & I don't know if he'll
get back to me today, but as soon as I find out Dr. whomever., I'll
gladly post my findings.
Craig.



   
Date: 08 May 2007 15:48:16
From: Craig Andrews
Subject: Re: size of tube from pump output to boiler inlet on silvia *ATT Dr.Xenon*

"Craig Andrews" <alt.coffee@deletethis.rogers.com > wrote in message
news:5a1g8tF2mlnlnU1@mid.individual.net...
>
> <Dr.Xenon1@gmail.com> wrote in message
> news:1178304429.155861.87920@l77g2000hsb.googlegroups.com...
>> On May 4, 11:55 am, "Craig Andrews"
>> <alt.cof...@deletethis.rogers.com>
>> wrote:
>>> <Dr.Xen...@gmail.com> wrote in message
>>>
>>> news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
>>>
>>> That's Bullshit & I posted you an answer for a Toronto source. I
>>> live in
>>> North Etobicoke & Fairview Fittings is about 10 minutes away from me
>>> &
>>> has everything you could possible need.
>>> Cheers!
>>> Craig.
>>
>> It turns out Fairview Fittings doesn't sell any metric tubing. They
>> referred me to a company called Hydraline, who referred me to a
>> company in Pickering called Williams, neither of whom carry PTFE
>> tubing.
>>
>
> Hmm, I figured that Fairview would have it, or know somone who does. I
> remembered another contact # from someome I met in a commercial
> supplier plumbing shop & the contact specializes in B.P.P.T., N.P.T.,
> & Metric fittings & tubing/s. I called them & someone in that division
> is looking for me. It's getting a little late in the day & I don't
> know if he'll get back to me today, but as soon as I find out Dr.
> whomever., I'll gladly post my findings.
> Craig.


Dr. Xenon, I've found the exact proper 6mm OD 4mm ID tubing for $1.60
CANADIAN per foot & am going to pick up the tubing for myself & you if
you'd like it. Working pressure is 23.5 bar. The run from Silvia's Ulka
vibe pump outlet to the inlet of the OPV is ONLY 7". I'm buying several
feet & you can contact me at my email address here to get your tubing.
Not bad, I just saved you 33.40! I only have a little over 1 hr to get
there, so won't be replying back here for a bit.
Cheers!
Craig.



    
Date: 08 May 2007 19:01:57
From: Craig Andrews
Subject: Re: size of tube from pump output to boiler inlet on silvia *ATT Dr.Xenon*

"Craig Andrews" <alt.coffee@deletethis.rogers.com > wrote in message
news:5ac2g1F2ojsqaU1@mid.individual.net...
>
> "Craig Andrews" <alt.coffee@deletethis.rogers.com> wrote in message
> news:5a1g8tF2mlnlnU1@mid.individual.net...
>>
>> <Dr.Xenon1@gmail.com> wrote in message
>> news:1178304429.155861.87920@l77g2000hsb.googlegroups.com...
>>> On May 4, 11:55 am, "Craig Andrews"
>>> <alt.cof...@deletethis.rogers.com>
>>> wrote:
>>>> <Dr.Xen...@gmail.com> wrote in message
>>>>
>>>> news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
>>>>
>>>> That's Bullshit & I posted you an answer for a Toronto source. I
>>>> live in
>>>> North Etobicoke & Fairview Fittings is about 10 minutes away from
>>>> me &
>>>> has everything you could possible need.
>>>> Cheers!
>>>> Craig.
>>>
>>> It turns out Fairview Fittings doesn't sell any metric tubing. They
>>> referred me to a company called Hydraline, who referred me to a
>>> company in Pickering called Williams, neither of whom carry PTFE
>>> tubing.
>>>
>>
>> Hmm, I figured that Fairview would have it, or know somone who does.
>> I remembered another contact # from someome I met in a commercial
>> supplier plumbing shop & the contact specializes in B.P.P.T., N.P.T.,
>> & Metric fittings & tubing/s. I called them & someone in that
>> division is looking for me. It's getting a little late in the day & I
>> don't know if he'll get back to me today, but as soon as I find out
>> Dr. whomever., I'll gladly post my findings.
>> Craig.
>
>
> Dr. Xenon, I've found the exact proper 6mm OD 4mm ID tubing for $1.60
> CANADIAN per foot & am going to pick up the tubing for myself & you if
> you'd like it. Working pressure is 23.5 bar. The run from Silvia's
> Ulka vibe pump outlet to the inlet of the OPV is ONLY 7". I'm buying
> several feet & you can contact me at my email address here to get your
> tubing. Not bad, I just saved you 33.40! I only have a little over 1
> hr to get there, so won't be replying back here for a bit.
> Cheers!
> Craig.

Picked up the tubing & I got there just under the wire, I was the last
person to be in the warehouse/customer pickup section as they closed
abot 10 minutes later. {;-D
I got your email @ 5:12pm & just got back in after dinner out @ 6:45pm.
Off to email you back Xenon.
Craig.



     
Date: 09 May 2007 23:59:27
From: Craig Andrews
Subject: Re: size of tube from pump output to boiler inlet on silvia *ATT Dr.Xenon*

"Craig Andrews" <alt.coffee@deletethis.rogers.com > wrote in message
news:5acdr5F2oersoU1@mid.individual.net...
>
> "Craig Andrews" <alt.coffee@deletethis.rogers.com> wrote in message
> news:5ac2g1F2ojsqaU1@mid.individual.net...
>>
>> "Craig Andrews" <alt.coffee@deletethis.rogers.com> wrote in message
>> news:5a1g8tF2mlnlnU1@mid.individual.net...
>>>
>>> <Dr.Xenon1@gmail.com> wrote in message
>>> news:1178304429.155861.87920@l77g2000hsb.googlegroups.com...
>>>> On May 4, 11:55 am, "Craig Andrews"
>>>> <alt.cof...@deletethis.rogers.com>
>>>> wrote:
>>>>> <Dr.Xen...@gmail.com> wrote in message
>>>>>
>>>>> news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
>>>>>
>>>>> That's Bullshit & I posted you an answer for a Toronto source. I
>>>>> live in
>>>>> North Etobicoke & Fairview Fittings is about 10 minutes away from
>>>>> me &
>>>>> has everything you could possible need.
>>>>> Cheers!
>>>>> Craig.
>>>>
>>>> It turns out Fairview Fittings doesn't sell any metric tubing.
>>>> They
>>>> referred me to a company called Hydraline, who referred me to a
>>>> company in Pickering called Williams, neither of whom carry PTFE
>>>> tubing.
>>>>
>>>
>>> Hmm, I figured that Fairview would have it, or know somone who does.
>>> I remembered another contact # from someome I met in a commercial
>>> supplier plumbing shop & the contact specializes in B.P.P.T.,
>>> N.P.T., & Metric fittings & tubing/s. I called them & someone in
>>> that division is looking for me. It's getting a little late in the
>>> day & I don't know if he'll get back to me today, but as soon as I
>>> find out Dr. whomever., I'll gladly post my findings.
>>> Craig.
>>
>>
>> Dr. Xenon, I've found the exact proper 6mm OD 4mm ID tubing for $1.60
>> CANADIAN per foot & am going to pick up the tubing for myself & you
>> if you'd like it. Working pressure is 23.5 bar. The run from Silvia's
>> Ulka vibe pump outlet to the inlet of the OPV is ONLY 7". I'm buying
>> several feet & you can contact me at my email address here to get
>> your tubing. Not bad, I just saved you 33.40! I only have a little
>> over 1 hr to get there, so won't be replying back here for a bit.
>> Cheers!
>> Craig.
>
> Picked up the tubing & I got there just under the wire, I was the last
> person to be in the warehouse/customer pickup section as they closed
> abot 10 minutes later. {;-D
> I got your email @ 5:12pm & just got back in after dinner out @
> 6:45pm.
> Off to email you back Xenon.
> Craig.


Hi Michael, I've sent you 2 emails after your 1st email contact with me
on Tues May 8th @ 5:12pm., one a few hrs later @ 7:33pm on the 8th &
again Wed the 9th @ 8:10pm. So I've had no contact from you since
then... Did you receive my 2 email please?
Regards,
Craig.



 
Date: 04 May 2007 11:28:08
From:
Subject: Re: size of tube from pump output to boiler inlet on silvia
On May 4, 11:55 am, "Craig Andrews" <alt.cof...@deletethis.rogers.com >
wrote:
> That's Bullshit & I posted you an answer for a Toronto source. I live in
> North Etobicoke & Fairview Fittings is about 10 minutes away from me &
> has everything you could possible need.

Thanks for the referral. Your post didn't appear in Google Groups or
my email
box (as a matter of fact, my post about McMaster refusing to ship
didn't appear
either, although I posted it through GG).

I will pay a visit to Fairview Fittings.



 
Date: 04 May 2007 11:55:25
From: Craig Andrews
Subject: Re: size of tube from pump output to boiler inlet on silvia

<Dr.Xenon1@gmail.com > wrote in message
news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
> Bummer. McMaster Carr said they can't send me the tubing "due to the
> ever increasing complexity of United States export regulations." Oh
> well, I guess it's a good thing they're keeping the terrorists from
> enjoying their espresso.
>
>
>

That's Bullshit & I posted you an answer for a Toronto source. I live in
North Etobicoke & Fairview Fittings is about 10 minutes away from me &
has everything you could possible need.
Cheers!
Craig.



 
Date: 04 May 2007 11:13:22
From: Craig Andrews
Subject: Re: size of tube from pump output to boiler inlet on silvia

<Dr.Xenon1@gmail.com > wrote in message
news:1178289998.173305.81830@e65g2000hsc.googlegroups.com...
> Bummer. McMaster Carr said they can't send me the tubing "due to the
> ever increasing complexity of United States export regulations." Oh
> well, I guess it's a good thing they're keeping the terrorists from
> enjoying their espresso.
>
>
>

Check out Fairview Fittings & Manufacturing Ltd, Head Office 449 Attwell
Drive, Toronto, Ontraio, M9W 5C4 Tel: 416-675-4233.
http://www.fairviewfittings.com/index.html
They have what ya need. I'm almost in the same predicament. Here's the
pdf link for the Master Catalog;
http://www.fairviewfittings.com/file_library/cats/121_Master_Catalogue_2006.pdf
Cheers!
Craig.